Outdoor LED Power Supply, 100W
Request a Quote
Features:
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
The outdoor power supply is up to 93% efficient
Protections: Short circuit / Over current / Over voltage / Over temperature
Cooling by free air convection
OCP point adjustable through output cable or internal potentiometer
IP67 design for outdoor lighting supply
Class 2 power unit
Three-in-one dimming function (1 〜10Vdc or PWM signal or resistance)
Suitable for LED lighting and street lighting applications
Compliance to worldwide safety regulations for LED lighting supply
Suitable for dry / damp / wet locations
Technical Specification:
| MODEL | PW100-24D-040A-MW | |
| OUTPUT | DC VOLTAGE | 24V |
| CONSTANT CURRENT REGION Note.4 | 12-24V | |
| RATED CURRENT | 4A | |
| RATED POWER | 96W | |
| RIPPLE & NOISE (max.) Note.2 | 150mVp-p | |
| VOLTAGE ADJ. RANGE Note.6 | 22 -27V | |
| CURRENT ADJ. RANGE | Can be adjusted by internal potentiometer | |
| 2.5 ~4A | ||
| VOLTAGE TOLERANCE Note.3 | ±1.0% | |
| LINE REGULATION | ±0.5% | |
| LOAD REGULATION | ±0.5% | |
| SETUP, RISE TIME Note.8 | 1200ms,50ms/115VAC 500ms,50ms/230VAC at full load | |
| HOLD UP TIME (Typ .) | 16ms at full load 230VAC /115VAC | |
| INPUT | VOLTAGE RANGE Note.5 | 90 -305VAC 127-431VDC |
| FREQUENCY RANGE | 47~63Hz | |
| POWER FACTOR (Typ .) | PF>0.98/115VAC, PF>0.95/230VAC, PF>0.93/277VAC at full load (Please refer to "Power Factor Characteristic" curve) | |
| TOTAL HARMONIC DISTORTION | THD< 20% when output loading ≥ 60% at 115VAC/230VAC input and output loading ≥ 75% at 277VAC input | |
| EFFICIENCY (Typ .) | 93% | |
| AC CURRENT (Typ . ) | 1.2A /115VAC 0.55A/230VAC 0.5A/277VAC | |
| INRUSH CURRENT (Typ . ) | COLD START 60A(twidth =415m s measured at 50% Ipeak ) at 230VAC | |
| LEAKAGE CURRENT | <0.75mA/277VAC | |
| PROTECTION | OVER CURRENT | 95-106% |
| Protection type: Constant current limiting, recovers automatically after the cause of the fault is removed | ||
| SHORT CIRCUIT | Constant current limiting, recovers automatically after the cause of the fault is removed | |
| OVERVOLTAGE | 28-34V | |
| Protection type: Shut down o/p voltage with auto-recovery or re-power on to recovery | ||
| OVER TEMPERATURE | Shut down o/p voltage, recovers automatically after temperature goes down |
| ENVIRONMENT | WORKING TEMP. | -40 ~ 70℃ (Refer to "Derating Curve") |
| WORKING HUMIDITY | 20 ~ 95% RH non-condensing | |
| STORAGE TEMP., HUMIDITY | -40 ~ 80℃ , 10-95% RH | |
| TEMP. COEFFICIENT | ± 0.03%℃ (0-50℃ ) | |
| VIBRATION | 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X,Y,Z axes | |
| SAFETY& EMC | SAFETY STANDARDS Note.7 | UL8750, CSAC22.2 No. 250.0-08, EN61347-1, EN61347-2-13 independent IP67 ,J61347-1, J61347- 2-13 approved; design refer to UL60950-1, TUV EN60950-1 |
| WITHSTAND VOLTAGE | I/P-O/P: 3.75KVAC I/P-FG: 2KVAC O/P-FG : 1.5KVAC | |
| ISOLATION RESISTANCE | I/P-O/P, I/P-FG , 0/P-FG:100M Ohms/500VDC/25℃ /70% RH | |
| EMC EMISSION | Compliance to EN55015, EN55022 (CISPR22) Class B, EN61000-3-2 Class C ≥60% load); EN61000-3-3 | |
| EMC IMMUNITY | Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN61547, EN55024 , light industry level (surge 4KV), criteria A | |
| OTHERS | MTBF | 192.2K hrs min. MIL-HDBK-217F (25℃ ) |
| DIMENSION | 220*68*38.8mm(L*W*H) | |
| PACKING | 1.12Kg ; 12pcs/14.4Kg/0.8CUFT | |
| NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. | |
| 2. Ripple and noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf and 47uf parallel capacitor. | ||
| 3. Tolerance: indudes set up tolerance, line regulation and load regulation. | ||
| 4. Please refer to "Driving Methods of LED Module." | ||
| 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. | ||
| 6. A-type only. | ||
| 7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1 , and FCC parti8. | ||
| 8. Length of set up time is measured at cold first start. Turning the power supply ON/OFF quickly may increase the set up time. | ||
| 9. The power supply is considered a separate component that will operate in combination with the final equipment. Since EMC performance will be affected by its installation, the final equipment manufacturers must re-qualify EMC Directives on the installed product. | ||
| 10. Refer to warranty statement. | ||
| 11. To fulfill requirements of the latest ErP regulations for lighting fixtures, this LED power supply can only be used behind a switch that's not permanently connected to the main system. | ||
Downloads
Related products
Send Message
Other Products
Most Recent
More
Other Products
Videos
