Aluminum Electrolytic Capacitor, CD60 Series Manufacturer

Aluminum Electrolytic Capacitor, CD60 Series

Request a Quote

View All: http://ppfilm-capacitor.com/3-2-dp-dc-link-filter-capacitor.html

, CD60 Series

Housed in a tubular case made of metal, PF resin, or engineering plastics, the CD60 series aluminum electrolytic capacitor uses pure aluminum foil as anode, covered with a barrier layer of aluminum oxide which acts as a dielectric. The electrolyte, or cathode, is non-solid. Two welded metal tabs, cables or wires stick out from the case as leads. The non-solid capacitor or e-cap is widely used as a motor capacitor in single phase AC motors running off of 50-60Hz and 110v-330v power. It gives the motor a high starting torque when the motor tries to start up at a low current.

Model Selection

SF229

Aluminum Electrolytic Capacitor, SF229

Operating Temperature	-25- 55 °C
Rated Voltage	110~330VAC
Capacitance Value	50~1000μF
Capacitance Tolerance	0~ 20%
Loss Tangent (tgδ) (20°C , 100Hz)	tgδ≤0.10, tgδ≤0.l5
Dielectric Breakdown Voltage	55 °C , 110-165VAC power supply, 1 second on, 59 seconds off, lasting 30000 cycles
	55 °C , 220-330VAC power supply, 1 second on, 59 seconds off, lasting 15000 cycles
	Variation of Capacitance: ±15% of Initial Measured Value
	Loss Tangent :≤0.20
Dielectric Breakdown Voltage (between terminals)	Apply 1.2 times the standard operating voltage between two terminals and hold that voltage for 2 seconds.
Dielectric Breakdown Voltage (between the terminal and case）	2000VAC, lasting for 2 seconds without breakdown

Technical Specs

Nominal Capacitance Value µF	110V_AC		125V_AC		160V_AC		250V_AC		300V_AC
	D	H	D	H	D	H	D	H	D	H
50	34	60	34	60	34	60	34	80	34	80
75									42
100				80		80	42		45	88
150		80			42		50	95	50	100
200
300	42		42		45	88		100	55
400	45	88	45	88	50	95	55		60
600	50	95	50	95			60			120
800		100		100	55	100
1000	55		55

SF230

Aluminum Electrolytic Capacitor, SF230

Operating Temperature	-25- 55 °C
Rated Voltage	110~330VAC
Standard Capacitance Value	50~1000μF
Standard Capacitance Tolerance	0~ 20%
Loss Tangent ( tgδ ) (20 °C , 100Hz)	tgδ≤0.10, tgδ≤0.l5
Dielectric Breakdown Voltage	55 °C , 110-165VAC, 1 second on, 59 seconds off, lasting 30000 cycles
	55 °C , 220-330VAC, 1 second on, 59 seconds off, lasting 15000 cycles
	Variation of Capacitance: ±15% of initial measured value
	Loss Tangent :≤0.20
Dielectric Breakdown Voltage (between terminals)	Apply 1.2 times the standard operating voltage. No breakdown within 2 seconds.
Dielectric Withstand Test (between the terminal and the case)	2000VAC, lasting for 10 seconds without breakdown

Technical Specs

Nominal Capacitance µF	110V_AC		125V_AC		160V_AC		250V_AC		300V_AC
	D	H	D	H	D	H	D	H	D	H
50	34	60	34	60	34	60	34	80	34	80
75									42
100				80		80	42		45	88
150		80			42		50	95	50	100
200
300	42		42		45	88		100	55
400	45	88	45	88	50	95	55		60
600	50	95	50	95			60			120
800		100		100	55	100
1000	55		55

SF231

Aluminum Electrolytic Capacitor, SF231

Operating Temperature	-40~ 65 °C
Rated Voltage	110-330VAC
Standard Capacitance Value	21~1536uF
Loss Tangent ( tgδ ) (20 °C , 100Hz)	tgδ≤0.10
Dielectric Breakdown Voltage	The test lasts 12500 to 50000 cycles, each cycle holding the same voltage for 1 second in 0.5 to 4 minutes. Capacitors with different operating voltages and capacitance values will go through different tests. All tests are performed in line with ANSI/EIA 463-A/B standards.
Dielectric Breakdown Voltage (between terminals)	Apply 1.25 times the working voltage, no breakdown and no explosion within 2 seconds
Dielectric Breakdown Voltage (between the terminal and the case)	2000VAC, lasting for 10 seconds with no breakdown.

Technical Specs

Nominal Capacitance Value MFD	125V_AC		165V_AC		250V_AC		330V_AC
21-25	36.50		36.50	69.85	36.50	69.85	36.50	69.85
25-30
30-36							46.02	85.72
36-43
43-52						85.72
47-56
53-64
64-77					46.02
72-86
88-106				85.72		112.12	52.37	111.12
108-130							65.50
124-149
130-156			46.02
145-174
161-193					52.37
189-227		85.72
216-259					65.50
233-280				111.12
243-292		11.12
270-324
324-389		85.72	52.37
340-408	46.02
378-454
400-480
430-516			65.50
460-552
540-648		11.12
590-708
645-774	52.37
708-850
720-964
800-960

SF232

Aluminum Electrolytic Capacitor, SF232

Operating Temperature	-40~ 65 °C
Rated Voltage	110-330VAC
Standard Capacitance Value	21~1536uF
Loss Tangent ( tgδ ) (20 °C , 100Hz)	tgδ≤0.10
Dielectric Breakdown Voltage	Apply a test voltage to the capacitor for 1 second. Time interval between 2 cycles is 0.5 to 4 minutes. The capacitor should last 12500 to 50000 cycles. Standards compliance: ANSI/EIA 463-A/B
Voltage Withstand Test (between terminals)	Apply 1.25 times the operating voltage. No breakdown or explosion within 2 seconds
Voltage Withstand Test (between the terminal and the case)	2000VAC, lasting for 10 second, with no breakdown or explosion

Capacitance, Voltage and Size

Nominal Capacitance Value MFD	125V_AC		165V_AC		250V_AC		330V_AC
21-25	36.50		36.50	69.85	36.50	69.85	36.50	69.85
25-30
30-36							46.02	85.72
36-43
43-52						85.72
47-56
53-64
64-77					46.02
72-86
88-106				85.72		112.12	52.37	111.12
108-130							65.50
124-149
130-156			46.02
145-174
161-193					52.37
189-227		85.72
216-259					65.50
233-280				111.12
243-292		11.12
270-324
324-389		85.72	52.37
340-408	46.02
378-454
400-480
430-516			65.50
460-552
540-648		11.12
590-708
645-774	52.37
708-850
720-964
800-960