SNMP Managed Media Converter
1. HiOSO SNMP managed media converter is a fiber network tool that can be categorized into 100M FC830AM series and 1000M FC830AGM series. The whole system comprises the 3U rack FTC-16M, M830AC NMS card, card type converter, and the remote controller.
2. This optical network unit supports SNMP, WEB, TELNET, serial port management, and software upgrade. It can not only supervise working conditions, but also configure the mode of each local media converter in the slot and remote media converter connected to the other side.
3. The SNMP managed media converter is fully compatible with network cards, repeaters, hubs, switches and others. Also, it offers cost-effective hardware support to the information transmission of broadband private network and fiber optical citywide LAN.
Features of theSNMP Managed Media Converter
1. Web-based graphic management interface of the SNMP protocol
2. Support local and remote Link Fault Pass Through (LFP) configuration.
3. Ethernet port supports MDI-MDIX Auto Crossover. Both straight-through and crossover network cables can be automatically identified.
4. This switch media converter is built to meet different standards including IEEE 802.3u 100BASE-FX/TX, IEEE802.3 10BASE-T, and more.
5. It supports IEEE 802.1Q VLAN and other protocols.
6. Ethernet port supports 10/100/1000M, full and half duplex self-adaptation.
7. Support automatic detection of MDI / - MDIX.
8. Support transmission distance up to 120 kilometers in dual fiber.
9. Support Spanning Tree Protocol (STP) to construct a redundant network.
10. Support hot swapping when in use of a module card in rack equipment.
| Size | 32mm (H) x 165mm (W) x 128mm (D) |
| Operating Temperature | -10 ~﹢55℃ |
| Storage Temperature | -40 ~﹢70℃ |
| Power Supply | AC220V / DC ﹣ 48V |
| Multimode Fiber: 62.5/125, 50/125, 100/140μm | |
| 100M: MM2km or MM5km 1000M: MM220m or MM550m | Output power: -20 ~ -18dBm |
| Receiving sensitivity: < -31dBm | |
| Distance: 0 ~ 2km or 0 ~ 5km | |
| Connector: SC (standard) | |
| Type: dual-fiber | |
| Wavelength: 850nm/1310nm | |
| Single-mode Fiber: 9/125, 8.3/125, 8.7/125 or 10/125μm | |
| 25km | Distance: 0 ~ 25km |
| Output power: -15 ~ -8dBm (dual-fiber), -14 ~ -8dBm (single-fiber) | |
| Receiving sensitivity: < -34dBm (dual-fiber) , < -33dBm (single-fiber) | |
| Connector: SC (standard) | |
| Type: single-fiber / dual-fiber | |
| Wavelength: 1310nm/1550nm (single-fiber), 1310nm (dual-fiber) | |
| 40km | Distance: 0 ~ 40km |
| Output power: -10 ~ -5dBm (dual-fiber), -9 ~ -5dBm (single-fiber) | |
| Receiving sensitivity: < -36dBm (dual-fiber), < -33dBm (single-fiber) | |
| Connector: SC (standard) | |
| Type: single-fiber / dual-fiber | |
| Wavelength :1310nm/1550nm (single-fiber), 1310nm (dual-fiber) | |
| 60km | Distance: 0 ~ 60km (when less than 15km, use attenuator) |
| Output power: -5 ~ 0dBm (dual-fiber), -6 ~ 0dbm (single-fiber) | |
| Receiving sensitivity: < -36dBm | |
| Connector: SC (standard) | |
| Type: single-fiber / dual-fiber | |
| Wavelength: 1310nm/1550nm (single-fiber), 1310nm (dual-fiber) | |
| 80km | Distance: 0 ~ 80km (when less than 15km, use attenuator) |
| Output power: -8 ~ -2dBm (dual-fiber), -3 ~ 3dbm (single-fiber) | |
| Receiving sensitivity: < -36dBm | |
| Connector: SC (standard) | |
| Type: single-fiber / dual-fiber | |
| Wavelength: 1310nm/1550nm (1490/1550nm) (single-fiber), 1550nm (dual-fiber) | |
| 100km | Distance: 0 ~ 100km (when less than 15km, use attenuator) |
| Output power: -6 ~ -1dBm | |
| Receiving sensitivity: < -38dBm | |
| Connector: SC (standard) | |
| Type: single-fiber / dual-fiber | |
| Wavelength: 1310nm/1550nm (1490/1550nm) (single-fiber), 1550nm (dual-fiber) | |
| 120km | Distance: 0 ~ 120km (when less than 15km, use attenuator) |
| Output power: -5 ~ 0dBm | |
| Receiving sensitivity: < -38dBm | |
| Connector: SC (standard) | |
| Type: dual-fiber | |
| Wavelength: 1550nm | |
Solution
The SNMP managed media converter is fully compliant with 10Base-T, 100Base-TX, 100Base-Fx and IEEE 802.3x International Standard etc
